The Mazda K-series automobile engine is a short stroke 60° 24-valve V6 with belt-driven DOHC and all-aluminium construction. Displacements range from 1.8 L to 2.5 L. They all use a 27-degree DOHC valvetrain with directly actuated hydraulic bucket lifters. The K-series also features a highly rigid aluminum split-crankcase engine block design with 4-bolt mains with additional bolts securing the lower block, an internally balanced forged steel crankshaft with lightweight powder forged carbon steel connecting rods. They were designed with the intent of being as compact as possible for short-hood front-wheel drive applications.
One unique innovation of the K-series was the introduction of Variable Resonance Induction System (VRIS). Based on the Helmholtz resonance principle, the intake manifold is equipped with 3 chambers tuned to a specific resonant frequency. The computer dynamically switches between each resonant chamber to achieve the appropriate resonant frequency for the engine's rpm. This effect optimizes volumetric efficiency over a given rpm range to provide maximum torque over the entire rpm range. VRIS is used on the K8, KF, and KL but nearly all modern Mazda V6s are now using this technology.
The K-series all have a 7,000Â rpm redline with 7500-7800Â rpm limiter, which given the engine design is conservative. The KJ-ZEM Miller cycle engine had a 6,000Â rpm redline, but was only available with an automatic transmission.
The 1.8 L (1,845 cc) K8 is among the smallest production V6 engines ever; and also the first K-series engine to be used in a Mazda car (in the Mazda MX-3). It was a DOHC 4-valve design with VRIS and a bore and stroke of 75 mm × 69.6 mm (2.95 in × 2.74 in). It produced 130 hp (97 kW; 132 PS) in US trim (sometimes referred to as "K8-DE"), and 135 hp (101 kW; 137 PS) in Japanese trim (the "K8-ZE") on introduction in 1991 and 144 hp (107 kW; 146 PS) and 115 lb⋅ft (156 N⋅m) at its best. The displacement was held under 2000cc to minimize the annual Japanese road tax obligation.
Applications:
The 2.3 L (2,255 cc) 80.3 mm × 74.2 mm (3.16 in × 2.92 in) bore and stroke, KJ-ZEM was one of Mazda's most technologically advanced engines. It employs the "Miller cycle" which uses a supercharger to increase compression efficiency by decreasing the compression losses (i.e., flywheel energy used to compress the intake charge in the cylinder); and thereby increasing the net power output of the V6. It was used in the T-platform cars. The supercharger used is the twin-screw type with electronic boost control. Power output was 217 hp (162 kW; 220 PS) and 210 lb⋅ft (285 N⋅m). The KJ-ZEM was on the Ward's 10 Best Engines list for 1995 through 1998.
Applications:
The 2.5 L (2,497 cc) KL family uses an 84.5 mm × 74.2 mm (3.33 in × 2.92 in) bore and stroke. It includes the Japan-only KL-ZE, which produced 200 hp (149 kW; 203 PS) and 165 lb⋅ft (224 N⋅m). Another variant, the KL-DE (also known as the KL-03 outside the US, and fitted to 2.5-litre Ford Probes) was the worldwide version, with 164–174 bhp (122–130 kW; 166–176 PS) in various applications. In 1998 a revised version of the KL known as the KL-G4 was used in the 626. It featured solid lifters, a cast crankshaft to reduce rotating mass and a reworked intake system. The distributor was replaced with a Ford EDIS coil-pack ignition.
Mazda introduced a key technology with these engines, known as the Variable Resonance Induction System (VRIS). A series of two butterfly valves coupled with electronically controlled actuators varied the volume and length of a resonant chamber within the intake manifold. The valves actuate at particular engine frequencies (i.e. rpms) to produce optimal torque/horsepower output at any given engine speed. The valve operates to create three specific first-order resonant frequencies that increase cylinder air charge. All three resonances are used from 0 to 6250Â rpm (6800 for the KL-ZE). Above that threshold, the first primary resonant chamber is again used, but at this engine speed the pressure wave from the second-order resonant frequency aids in charging the cylinder.
We are a leading provider of Engines and Transmissions. We have provided customers with an unbeatable Price,
Unmatched Quality and excellent Customer Service for 20 years.
We use only top quality re-manufacturers to supply our clients with professionally re-manufactured Transmissions. All of our transmissions have factory backed warranties.
All of our engines and transmissions are rigorously tested and inspected prior to shipping. This allows us to warranty your engine to keep your vehicle on the road for years to come.
We provide access to Salvage yards and auto part retailers for automotive engine and transmissions .
Looking For a Specialist
Please Contact Now
1800-385-3915
Looking For a Specialist
Please Contact Now
1800-385-3915
PAY SECURELY WITH